Skip to content
Product Carbon Footprint
November 6, 2026
8 min read

Screening PCF, ISO 14067 or EPD: What Will Your Customer Accept?

By Morten Rosén, Co-founder & CEO, Future Fluent

ISO 14067
EPD
Screening PCF
Verification

A screening PCF allocates your company's emissions over your products. An ISO 14067 footprint is a product-level life cycle study following the ISO standard. An EPD is a broader, usually third-party verified declaration covering several environmental impacts. Which one your customer accepts depends on what they will use it for.

Quick facts

  • ISO 14067 sets requirements for quantifying a product's carbon footprint. It is a calculation standard, not a certificate.
  • ISO 14067 allows a partial footprint, such as cradle-to-gate, as long as the excluded stages are stated.
  • An EPD follows ISO 14025, covers several impacts, and is published by a programme operator, typically after independent verification. Construction products use EN 15804.
  • A screening PCF is derived from your company GHG inventory. It is fast and consistent, but it is not an ISO 14067 study.
  • For a customer's Scope 3 inventory, a screening PCF is a large step up from the spend-based estimate they would otherwise use.
  • For public product claims, tenders and construction projects, expect to need ISO 14067 work or an EPD.

What is the difference between a screening PCF, an ISO 14067 footprint and an EPD?

They differ in method, scope and verification. A screening PCF allocates company emissions to products. An ISO 14067 footprint models one product's life cycle following the standard. An EPD reports several environmental impacts, not only climate, under product category rules, and is typically verified and published.

A screening product carbon footprint, an ISO 14067 footprint and an EPD compared by what they measure, method, detail, verification, publication, time and cost
Screening PCFISO 14067 footprintEPD
What it measuresGreenhouse gases onlyGreenhouse gases onlySeveral impacts, including climate
MethodAllocation from the company GHG inventoryProduct life cycle assessment (ISO 14040/44)Life cycle assessment under product category rules (ISO 14025)
Product-specific detailLow to mediumHighHigh
VerificationNot verifiedCritical review possible, under ISO/TS 14071Typically independent verification before publication
PublishedShared with the customerShared or publishedRegistered with a programme operator
Time and costHours, once your inventory existsWeeks per productWeeks to months per product

The three are not rungs on a single ladder. An EPD answers a broader question than a carbon footprint, and a screening PCF answers a narrower one than an ISO study. The useful question is which one fits the job.

What does ISO 14067 require?

ISO 14067 requires a life cycle assessment of the product's greenhouse gas emissions and removals, following the principles of ISO 14040 and 14044. It allows a full or a partial footprint, a declared unit for partial ones, and requires the boundary and any exclusions to be stated.

Two common misunderstandings are worth clearing up. First, ISO 14067 does not certify anything on its own. There is no "ISO 14067 certificate" in the sense of a management system certificate. Second, review is not automatic. The standard describes a critical review performed according to ISO/TS 14071, and commentators read it as optional in most situations. When a supplier says its product is "ISO 14067 certified", the right follow-up is to ask who reviewed the study, and against what.

What is an EPD, and when do you need one?

An environmental product declaration is a standardised document reporting a product's life cycle impacts, including but not limited to climate. It follows ISO 14025 and the product category rules for its sector, and is registered by a programme operator, usually after independent verification. Construction products follow EN 15804.

You need an EPD when your market asks for one, which in practice means construction, public procurement and some tenders where environmental performance is scored. An EPD costs considerably more than a carbon footprint because it covers more impacts and goes through verification. If a customer only needs your climate figure for its Scope 3, an EPD is more than the job requires.

What is a screening PCF?

A screening PCF takes your company's cradle-to-gate emissions for a year and allocates them over the products you made, by mass or by revenue. Every product gets a footprint per unit from the same inventory, the same year and the same method, so the figures are consistent across your whole range.

The trade-off is detail. Two products of the same weight receive the same footprint under mass allocation, even if one needs much more energy to make. That is why a screening footprint is a starting point, not an end point. The method, with a worked example, is in how to calculate a product carbon footprint from your GHG inventory.

Which one will your customer accept?

That depends on what the customer will do with your figure. For their Scope 3 inventory, a screening PCF with a stated method is usually acceptable, and far better than a spend-based estimate. For public claims about a product, comparisons between products, tenders and construction, expect to need ISO 14067 work or an EPD.

A practical guide by use:

Which form of product footprint is usually enough, by what the customer will use the figure for
Your customer wants the figure forUsually enough
Its Scope 3 inventory under CSRD or the Voluntary StandardScreening PCF with method, year and primary data share
Tracking supplier progress year on yearScreening PCF, same method every year
A public claim about its own productISO 14067 footprint, ideally reviewed
A public comparison between productsReviewed ISO 14067 footprint, or EPDs under the same rules
Construction projects, many public tendersEPD (EN 15804 for construction)

When a customer asks for "a PCF", ask what it is for before you commission anything. The answer usually decides the format.

Does a screening PCF count as primary data?

Partly. The PACT Methodology measures this as the primary data share: the part of the footprint that comes from your own measured data. Your energy and fuel use are primary data. Emissions estimated from spend or average factors are secondary. A screening PCF should state its share honestly.

This matters more than the label on the method. A screening footprint with a high primary data share, built on your actual energy and fuel use and on supplier-specific data for your main materials, can be more informative than a modelled study built mostly on database averages.

Should you go straight to ISO 14067?

Usually not for your whole range. Start with a screening footprint for every product, which shows where your emissions concentrate. Then commission ISO 14067 studies or EPDs for the few products where a customer, a tender or a public claim actually requires one.

That sequence spends your budget where it changes something. Future Fluent's product footprint feature produces a screening PCF per product from your GHG inventory, with the method, primary data share and stage breakdown on a shareable datasheet. It is not a verified ISO 14067 study, and it says so on the datasheet. The bigger picture is in the product carbon footprint guide for manufacturers.

See which plan includes product carbon footprints →

Frequently asked questions

Is there such a thing as an ISO 14067 certificate?
Not in the sense of a management system certificate. ISO 14067 sets calculation requirements. A study can be critically reviewed against it, and the reviewer and scope of review are what to ask about.

Is a PCF the same as an EPD?
No. A PCF covers greenhouse gases only. An EPD reports several environmental impacts under product category rules and is usually independently verified before publication.

Can a screening PCF be used in a customer's Scope 3 inventory?
Usually yes, provided the method, boundary, year and primary data share are stated. It replaces a much less accurate spend-based estimate.

When do I need an EPD?
When your market requires one, most often in construction (EN 15804), public procurement and tenders that score environmental performance.